Microbial community diversity of an integrated constructed wetland used for treatment of sewage.

The microbial community diversity in Constructed Wetland System (CWS) plays a key role in the removal of pollutants from waste water. An integrated functional CWS developed at Neela Hauz Biodiversity Park, Delhi was selected to assess the diversity in composition and structure of microbial community diversity of sludge and sediment of CWS, based on metagenomic approach using 16S rRNA genes. The sediment showed higher diversity than sludge and both formed distinct clusters. The taxonomic structure of the microbial community of CWS is represented by 6,731 OTUs distributed among 2 kingdoms, 103 phyla, 227 classes, 337 orders, 320 families, 295 identified genera, and 84 identified species. The relative abundance of top 5 dominant phyla of sludge and sediment varied from 3.77% (Acidobacteria) to 35.33% (Proteobacteria) and 4.07% (Firmicutes) to 28.20% (Proteobacteria), respectively. The range of variation in relative abundance of top 5 dominant genera of sludge and sediment was 2.58% (Hyphomicrobium) to 6.61% (Planctomyces) and 2.47% (Clostridium) to 4.22% (Syntrophobacter), respectively. The rich microbial diversity of CWS makes it perform better in pollutants removal (59.91-95.76%) than other CWs. Based on the abundance values of taxa, the taxa are grouped under four frequency distribution classes-abundant (>20), common (10-19), rare (5-9), and very rare (1-4). The unique structure of microbial communities of integrated CWS is that the number of abundant taxa decreases in descending order of taxonomic hierarchy, while the number of rare and very rare taxa increases. For example, the number of abundant phyla was 14 and 21 in sludge and sediment, respectively and both communities have only 3 abundant genera each. This is in contrast to 4 and 17 very rare phyla in sludge and sediment, respectively and both the communities have 114 and 91 very rare genera, respectively. The outcomes of the study is that the integrated CWS has much higher microbial community diversity than the diversity reported for other CWs, and the rich diversity can be used for optimizing the performance efficiency of CWS in the removal of pollutants from waste water. Such structural diversity might be an adaptation to heterogeneous environment of CWS.

Novel Insights into Alkyl Polyglucoside Biosurfactant Promoting Anaerobic Dark Fermentation for Hydrogen Production in Sludge.

Anaerobic fermentation of excess sludge (ES) for hydrogen production is a crucial strategy for resource utilization and environmentally friendly treatment. However, the low hydrolysis efficiency of ES and the depletion of produced hydrogen have become the limiting factors for low hydrogen yield. This study innovatively applied the bio-based surfactant alkyl polyglucoside (APG) to enhance the efficiency of dark fermentation for hydrogen production from ES. When the APG content was 100 mg/g (calculated based on total suspended solids), the maximum hydrogen production reached 17.8 mL/g VSS, approximately 3.7 times that in the control group. Mechanistic analysis revealed that APG promoted the release of organic matter from ES. APG also facilitated the release of soluble protein and soluble polysaccharide, increasing the organic matter reduction rate to 34.8%, significantly higher than other groups. APG enhanced the accumulation of volatile fatty acids and promoted the proportion of small molecular carboxylic acids. Enzyme activity analysis revealed that APG promoted the activity of hydrolytic enzymes but inhibited the activity of hydrogen-consuming enzymes. The research results provide a green and environmentally friendly strategy for the efficient resource utilization of ES.

The influence of biochar from animal and plant on the transformation of phosphorus during paper mill sludge composting.

Biochar has effect on phosphorus adsorption, release, and transformation. This study compared the influence of biochar derived from animal (AB) and plant (PB) during paper mill sludge composting. Results indicated AB not only accelerated sludge decomposition but also had significantly higher levels of available phosphorus (AP) than PB and CK (no biochar), with AP contents in the order of AB > PB > CK. Compared to CK, AB was found to increase the relative abundance of thermophilic bacteria, and PB diversified the microbial community. Based on Pearson and RDA results, TOC/TN ratio (C/N) and organic matter (OM) explained above 50% of the variance in microbial community and phosphorus fractions. Thermophilic bacteria with high levels of OM and C/N promoted the conversion among labile and moderately labile organic phosphorus, moderately labile inorganic phosphorus, and AP. Biochar could enhance the AP conversion pathway, leading to increased levels of AP.

Improved hydrolysis of sewage sludge by air-assisted non-thermal plasma for enhanced biomethane recovery.

Conventional pretreatment technologies have been assessed to resolve the slow hydrolysis of sewage sludge, but high operating costs have prevented their wide use. This study investigated non-thermal plasma (NTP) technologies as an alternative to promote anaerobic digestion (AD). Various contact time (CT) and temperature (T) conditions were used to assess how NTP pretreatment improves the methane conversion of organics in sewage sludge. A multi-response surface model (RSM) using a central composite design (CCD) identified the optimal CT (4.6 h) and T (45 °C). This statistical optimization of NTP pretreatment led to an enhanced biochemical methane potential of 297 ± 46 mL CH4 g-1 COD by reducing operating cost as power consumption as low as 0.08 USD L-1. The result was comparable to those of other advanced oxidation processes (0.14 - 0.60 USD L-1) demonstrating that accelerated hydrolysis of sewage sludge using NTP pretreatment show potential for improving renewable energy recovery from sewage sludge.

Hybrid conditioning of ionic liquid coupling with H2SO4 to improve the dewatering performance of municipal sludge.

Municipal sludge generated from wastewater treatment plants can cause a serious environmental and economic burden. A novel hybrid conditioning strategy was developed to enhance the dewatering performance of sludge, employing 1-butyl-3-methylimidazolium trifluoromethanesulfonate ([C4mim][CF3SO3]) treatment combined with H2SO4 acidification. Following conditioning, the capillary suction time ( CST normalized ), the specific resistance of filtration (SRF), and moisture content of the treated sludge were decreased to 1.99 ± 0.24 (s·L/g TSS), 1.33 ± 0.05 (1012 m/kg), and 72.01 ± 0.94%, respectively. The results were superior to those achieved with sludge treated solely by H2SO4 acidification or [C4mim][CF3SO3] alone. The biomacromolecules within the sludge flocs were dissolved by [C4mim][CF3SO3], while simultaneously, the microorganisms were inactivated. Consequently, the colloidal-like structures of the sludge flocs were destroyed. Additionally, the ionizable functional groups of the biomacromolecules were instantly protonated by the introduced H+ ions, and their negative charges were neutralized during the H2SO4 acidification process. The presence of H+ ions promoted the weakening of electrostatic repulsion between the sludge flocs. As a result, an enhancement of sludge dewaterability was obtained after treatment with [C4mim][CF3SO3] and H2SO4 acidification. The finding of the intensification mechanism of sludge dewaterability brought by hybrid treatment of acidification and [C4mim][CF3SO3] provides novel insights into the field of sludge disposal.

Impact of temperature and residence time on sewage sludge pyrolysis for combined carbon sequestration and energy production.

Environmental challenges related to sewage sludge call for urgent sustainable management of this resource. Sludge pyrolysis might be considered as a sustainable technology and is anticipated to support measures for mitigating climate change through carbon sequestration. The end products of the process have various applications, including the agricultural utilization of biochar, as well as the energy exploitation of bio-oil and syngas. In this research, sewage sludge was pyrolyzed at 500 °C, 600 °C, 750 °C, and 850 °C. At each temperature, pyrolysis was explored at 1hr, 2hrs, and 3hrs residence times. The ratio (H/Corg)at was tapped to imply organic carbon stability and carbon sequestration potential. Optimum operating conditions were achieved at 750 °C and 2hrs residence time. Produced biochar had (H/Corg)at ratio of 0.54, while nutrients' contents based on dry weight were 3.99%, 3.2%, and 0.6% for total nitrogen (TN), total phosphorus (TP), and total potassium (TK), respectively. Electrical conductivity of biochar was lesser than the feed sludge. Heavy metals in biochar aligned with the recommended values of the International Biochar Initiative. Heat content of condensable and non-condensable volatiles was sufficient to maintain the temperature of the furnace provided that PYREG process is considered. However, additional energy source is demanded for sludge drying.

Near-complete recycling of real mix electroplating sludge as valuable metals via Fe/Cr co-crystallization and stepwise extraction route.

In electroplating sludge, iron (Fe) and aluminum (Al) are common impurities that need to be separated before recycling valuable heavy metals. However, the traditional Fe/Al separation process often leads to significant losses of heavy metals. To address this issue, a new approach was developed to sequentially separate Fe/Al and recycle chromium (Cr) and nickel (Ni) from real electroplating sludge. The sludge contained 4.5% Cr, 1.2% Al, 1.1% Ni, and 14.6% Fe. Initially, the sludge was completely dissolved in a mixture of hydrochloric and nitric acids. The resulting acid solution was then heated to 160 °C for 10 h with the addition of saccharose. This hydrothermal treatment led to the hydrolysis and crystallization of 98.3% of Fe, 31.8% of Cr, 1.1% of Al, and 4.9% of Ni, forming akaganeite-bearing particles. It was observed that the excessive amount of saccharose also improved the removal of Cr, Al, and Ni, but decreased the removal of Fe. After the hydrothermal treatment, the remaining supernatant was adjusted to different pH levels (1.9, 2.9, and 4.5, respectively), and then Al, Cr, and Ni were stepwise extracted using di-(2-ethylhexyl) phosphate acid (P204). The recycling efficiencies achieved were 97.4% for Al, 61.2% for Cr, and 89.3% for Ni. This approach provides a promising method for the stepwise separation of Fe/Al and the recycling of heavy metals from electroplating sludge.

Performance of a high-rate membrane bioreactor for energy-efficient treatment of textile wastewater.

High-rate membrane bioreactors (MBR), where the wastewater undergoes partial oxidation due to the applied short sludge retention time (SRT) and hydraulic retention time (HRT) values, retain the majority of the organic substances in the sludge through growth and biological flocculation. Thus, a raw material source with a high biomethane production potential is created for the widespread use of circular economy or energy-neutral plants in wastewater treatment. While high-rate MBRs have been successfully employed for energy-efficient treatment of domestic wastewater, there is a lack of research specifically focused on textile wastewater. This study aimed to investigate the textile wastewater treatment and organic matter recovery performances of an aerobic MBR system containing a hollow fiber ultrafiltration membrane with a 0.04 µm pore diameter. The system was initially operated at short SRTs (5 and 3 d) and different SRT/HRT ratios (5, 10, and 20) and subsequently at high-rate conditions (SRT of 0.5-2 d and HRT of 1.2-9.6 h) which are believed to be the most limiting conditions tested for treatment of real textile wastewater. The results showed that chemical oxygen demand (COD) removal averaged 77% even at SRT of 0.5 d and HRT of 1.2 h. Slowly biodegradable substrates and soluble microbial products (SMP) accumulated within the MBR at SRT of 0.5 and 1 d, which resulted in decreased sludge filterability. The observed sludge yield (Yobs) exhibited a considerable increase when SRT was reduced from 5 to 1 d. On the other hand, the SRT/HRT ratio displayed a decisive effect on the energy requirement for aeration.

Adsorption of sulfamethoxazole and lincomycin from single and binary aqueous systems using acid-modified biochar from activated sludge biomass.

The extensive use of pharmaceuticals has raised growing concerns regarding their presence in surface waters. High concentrations of sulfamethoxazole (SMX) and lincomycin (LIN), as commonly prescribed antibiotics, persist in various wastewaters and surface waters, posing risks to public health and the environment. Biochar derived from accessible biowaste, like activated sludge biomass, offers a sustainable and eco-friendly solution to mitigate antibiotic release into water systems. This study investigates the effectiveness of H3PO4-modified activated sludge-based biochar (PBC) synthesized through microwave (MW) heating for the adsorption of SMX and LIN antibiotics. The synthesis parameters of PBC were optimized using a central composite design considering MW power, time, and H3PO4 concentration. Characterization results validate the efficacy of the synthesis process creating a specific surface area of 365 m2/g, and well-developed porosity with abundant oxygen-containing functional groups. Batch and dynamic adsorption experiments were piloted to assess the adsorption performance of PBC in single and binary antibiotic systems. Results show that PBC exhibits a higher affinity for SMX rather than LIN, with maximum adsorption capacities of 45.6 mg/g and 26.6 mg/g, respectively. Based on kinetic studies chemisorption is suggested as the primary mechanism for SMX and LIN removal. Equilibrium studies show a strong agreement with the Redlich-Peterson isotherm, suggesting a composite adsorption mechanism with a greater probability of multilayer adsorption for both antibiotics. Hydrogen bonding and π-π electron sharing are suggested as the prevailing adsorption mechanisms of SMX and LIN on the modified biochar. Furthermore, a dynamic adsorption system was replicated using a fixed bed column setup, demonstrating effective removal of SMX and LIN from pure water and real wastewater samples using PBC-loaded hydrogel beads (PBC-B). These findings serve as crucial support for upcoming studies concerning the realistic application of sludge-based biochar in the removal of antibiotics from water systems.

Response of aerobic granular sludge under acute inhibition by polystyrene microplastics: Activity, aggregation performance, and microbial analysis.

In this study, the activity, aggregation performance, microbial community and functional proteins of aerobic granular sludge (AGS) in response to acute inhibition by different concentrations of polystyrene microplastics (PS-MPs) were investigated. As the PS-MPs concentration increased from 0 mg/L to 200 mg/L, the specific nitrogen removal rate and the activity of enzymes were inhibited. The inhibition of specific nitrite reduction rate (SNIRR) and specific nitrate reduction rate (SNRR) was most obvious at the PS-MPs concentration of 100 mg/L, and that of nitrite reductase (NIR) and nitrate reductase (NR) was most obvious at the concentration of 50 mg/L. But the inhibitory effects were mitigated at the concentration of 200 mg/L. The increase of reactive oxygen species (ROS) and lactate dehydrogenase (LDH) indicated that the cells were damaged with the increase of PS-MPs concentration. The content of proteins and polysaccharides in extracellular polymeric substances (EPS) decreased, especially the polysaccharides were more affected. Analysis of zeta potential, hydrophobicity and surface thermodynamics of AGS revealed that addition of PS-MPs was unfavorable for AGS aggregation. It was also found that bacteria genera associated with EPS secretion and nitrogen removal functions were inhibited, while functions associated with cell metabolism, protein synthesis and cell repair were enhanced. This also confirmed that acute inhibition of PS-MPs had a detrimental effect on the nitrogen removal and aggregation performance of AGS. This study can provide theoretical support for the operation of AGS reactors under microplastics impact load.

Enhancing the relative abundance of comammox nitrospira in ammonia oxidizer community decreases N2O emission in nitrification exponentially.

Comammox Nitrospira and canonical ammonia-oxidizing bacteria (cAOB) generally coexist in activated sludge. In present study, the effect of comammox Nitrospira on N2O production during nitrification of activated sludge was investigated. Comammox Nitrospira and cAOB were separately enriched in two nitrifying reactors, with respective relative abundance of approximately 98% in ammonia oxidizer community. The N2O emission factor (EF) of nitrification in comammox Nitrospira dominated reactor was 0.35%, consistently lower than that (2.2%) in cAOB dominated reactor. When increasing the relative abundance of comammox Nitrospira in ammonia oxidizer community, the N2O EF of nitrification decreased exponentially, which suggested that comammox Nitrospira not only decreased N2O production directly but also might have reduced N2O yield by cAOB. When cAOB dominated the ammonia oxidizer community of sludge, decreasing pH to 6.3, lowering DO to less than 0.5 mg/L, and increasing nitrite concentration enhanced N2O EF dramatically. When comammox Nitrospira became the dominant ammonia oxidizer, however, the N2O EF correlated to nitrite insignificantly and a low DO of 0.2 mg/L and weakly acidic pH (6.3) decreased N2O EF by approximately 70% and 60%, respectively. These results imply that enhancing the relative abundance of comammox Nitrospira in sludge is an effective way to reducing N2O emissions and can also offset the promoting effects of acidic pH, low DO, and high nitrite concentration on N2O production during nitrification.

Competitive adsorption of heavy metals onto xanthate-modified sludge hydrochar and its solidification as secondary minerals.

In this study, a sulfur-modified magnetic hydrochar was synthesized by grafting thiol-containing groups onto the sludge-derived hydrochar. The modified hydrochar exhibited effective adsorption of Cu2+, Pb2+, Zn2+, and Cd2+ over a wide pH range and in the presence of coexisting ions, and showed almost no secondary leaching in three acidic solutions. In the mult-metal ion system, the modified hydrochar exhibited maximum adsorption capacities were 39.38, 105.74, 26.53, and 38.11 mg g-1 for Cu2+, Pb2+, Zn2+, and Cd2+, respectively. However, the binding capacity and adsorption amount of modified hydrochar for metal ions were lower in the mult-metal ion system compared to the unit-metal ion system. Notably, Pb2+ showed a strong inhibitory effect on the adsorption of other heavy metal ions by modified hydrochar due to strong competition for xanthate functional groups. The Pb2+ occupied the xanthate and native functional groups (-OH, -NH2, and Fe-O etc.), leaving only a small amount of adsorption sites for Cu2+, Zn2+ and Cd2+. Simulation results further supported these findings, indicating that Pb2+ had the highest density profiles near the four functional groups, and the density profiles of the four heavy metals near the xanthate functional groups were greater compared to the other three functional groups. Furthermore, the SEM-EDS, TOF-SIMI, and XPS results indicated that modified hydrochar achieved excellent mineral binding mainly through electrostatic interaction, ion exchange, and chelation. Overall, these results highlight the sulfur-modified magnetic hydrochar as a highly efficient adsorbent for heavy metals in environmental applications.

Thermo-catalytic pyrolysis of sewage sludge and techno-economic analysis: The effect of synthetic zeolites and natural sourced catalysts.

This work focuses to the value added utilization of animal sewage sludge into gases, bio-oil and char using synthetic zeolite (ZSM-5 and Y-zeolite) and natural sourced (diatomite, kaolin, perlite) materials as catalysts. Pyrolysis was performed in a one-stage bench-scale reactor at temperatures of 400 and 600 °C. The catalyst was mixed with the raw material before the pyrolysis. Catalysts had a significant effect on the yield of products, because the amount of volatile products was higher in their presence, than without them. In case of kaolin, due to the structural transformation occurring between 500-600 °C, a significant increase in activity was observed in terms of pyrolysis reactions resulting in volatiles. The hydrogen content of the gas products increased significantly at a temperature of 600 °C and in thermo-catalysts pyrolysis. In the presence of catalysts, bio-oil had more favourable properties.

Effects of municipal sludge composition on hydrothermal liquefaction products: Aqueous phase characterization and biodegradability assessment.

Hydrothermal liquefaction (HTL) aqueous phases derived from mixed sludge and digested sludge of two wastewater treatment plants (WWTP) were characterized considering variations in primary-secondary sludge ratios, an aspect previously overlooked in the literature. Mixed sludge was obtained by mixing primary and secondary sludge to simulate high primary sludge, average, and high secondary sludge cases. Aerobic and mesophilic/thermophilic anaerobic biodegradability tests were conducted. Higher chemical oxygen demand, total ammonium-N, orthophosphate-P, fatty acids, and N-heterocycles in HTL aqueous samples were detected as the secondary sludge ratio increased in mixed sludge. A similar trend was observed in the biodegradability tests. Characteristics of HTL aqueous derived from mixed sludge of WWTP 1 showed much higher variation, whereas WWTP 2 mixed sludge was not affected significantly by primary-secondary sludge ratios. Finally, the biodegradability levels of HTL aqueous samples were determined to be 69-78 % under aerobic, 58-70 % under mesophilic anaerobic, and 42-56 % under thermophilic anaerobic conditions.

Biogas upgrading performance and underlying mechanism in microbial electrolysis cell and anaerobic digestion integrated system.

The productivity and efficiency of two-chamber microbial electrolysis cell and anaerobic digestion integrated system (MEC-AD) were promoted by a complex of anaerobic granular sludge and iron oxides (Fe-AnGS) as inoculum. Results showed that MEC-AD with Fe-AnGS achieved biogas upgrading with a 23%-29% increase in the energy recovery rate of external circuit current and a 26%-31% decrease in volatile fatty acids. The energy recovery rate of MEC-AD remained at 52%-57%, indicating a stable operation performance. The selectively enriched methanogens and electroactive bacteria resulted in dominant hydrogenotrophic and acetoclastic methanogenesis in the cathode and anode chambers. Mechanistic analysis revealed that MEC-AD with Fe-AnGS led to specifically upregulated enzymes related to energy metabolism and electron transfer. Fe-AnGS as inoculum could improve the long-term operation performance of MEC-AD. Consequently, this study provides an efficient strategy for biogas upgrading in MEC-AD.

A mass balance approach for quantifying the role of natural decay and fate mechanisms on SARS-CoV-2 genetic marker removal during water reclamation.

The recent SARS-CoV-2 outbreak yielded substantial data regarding virus fate and prevalence at water reclamation facilities (WRFs), identifying influential factors as natural decay, adsorption, light, pH, salinity, and antagonistic microorganisms. However, no studies have quantified the impact of these factors in full scale WRFs. Utilizing a mass balance approach, we assessed the impact of natural decay and other fate mechanisms on genetic marker removal during water reclamation, through the use of sludge and wastewater genetic marker loading estimates. Results indicated negligible removal of genetic markers during P/PT (primary effluent (PE) p value: 0.267; preliminary and primary treatment (P/PT) accumulation p value: 0.904; and thickened primary sludge (TPS) p value: 0.076) indicating no contribution of natural decay and other fate mechanisms toward removal in P/PT. Comparably, adsorption and decomposition was found to be the dominant pathway for genetic marker removal (thickened waste activated sludge (TWAS) log loading 9.75 log10 GC/day); however, no estimation of log genetic marker accumulation could be carried out due to high detections in TWAS. PRACTITIONER POINTS: The mass balance approach suggested that the contribution of natural decay and other fate mechanisms to virus removal during wastewater treatment are negligible compared with adsorption and decomposition in P/PT (p value: 0.904). During (P/PT), a higher viral load remained in the (PE) (14.16 log10 GC/day) compared with TPS (13.83 log10 GC/day); however, no statistical difference was observed (p value: 0.280) indicting that adsorption/decomposition most probably did not occur. In secondary treatment (ST), viral genetic markers in TWAS were consistently detected (13.41 log10 GC/day) compared with secondary effluent (SE), indicating that longer HRT and the potential presence of extracellular polymeric substance-containing enriched biomass enabled adsorption/decomposition. Estimations of total solids and volatile solids for TPS and TWAS indicated that adsorption affinity was different between solids sampling locations (p value: <0.0001).

Evaluating drained water quality in a pilot worm-sludge treatment reed bed planted with Arundo donnas in the Mediterranean climate.

This study evaluated the impact of incorporating earthworms (Eisenia fetida) on the drained water quality from a sludge treatment reed bed. The experiment encompassed four setups of treatment beds in two replicates: planted with Arundo donax and addition of earthworms, planted without earthworms, unplanted with earthworms, and treatment bed without plants nor earthworms as control. The units were fed every two weeks with mixed sewage sludge, a blend of primary and secondary sludge over 24 cycles. The mixed sewage sludge had mean dry and volatile solid contents of 24.71 g.DS.L-1 (± 13.67) and 19.14 g.VS.L-1 (± 10.29) resulting a sludge loading rate of 43.59 kg.DS.m-2.year-1 (± 14.49). The inclusion of earthworms in the planted unit reduced release masses of total suspended solids, chemical oxygen demand, nitrate and phosphorous by 43, 45, 75 and 45 % compared to the planted unit. Plant biomass production increased by 43 % with the earthworm presence. The removal efficiency of the units improved after a ramp-up phase (after six months feeding) of which the concentration of TSS, COD and Escherichia coli met limits for water reuse while nitrogen components and phosphorous surpassed the limits. The planted unit with earthworms removed 99 and 99 % of TSS and COD, respectively. Overall, water loss namely through evapotranspiration and earthworm hydration need, positively correlated with pollutant concentration, and earthworm-planted unit had 46 % higher water loss compared to control unit.

Effects of carbon-based conductive materials on semi-continuous anaerobic co-digestion of organic fraction of municipal solid waste and waste activated sludge.

Organic fraction of municipal solid waste (OFMSW) and waste activated sludge (WAS) are the most produced organic waste streams in urban centres. Their anaerobic co-digestion (AcoD) allows to generate methane (CH4) and digestate employable as renewable energy source and soil amendment, respectively, fully in accordance with circular bioeconomy principles. However, the widespread adoption of such technology is limited by relatively low CH4 yields that fail to bridge the gap between benefits and costs. Among strategies to boost AcoD of OFMSW and WAS, use of conductive materials (CMs) to promote interspecies electron transfer has gained increasing attention. This paper presents one of the few experimental attempts of investigating the effects of four different carbon(C)-based CMs (i.e., granular activated carbon - GAC, graphite - GR, graphene oxide - GO, and carbon nanotubes - CNTs) separately added in semi-continuous AcoD of OFMSW and thickened WAS. The presence of C-based CMs has been observed to improve CH4 yield of the control process. Specifically, after 63 days of operation (concentrations of GAC and GR of 10.0 g/L and of GO and CNTs of 0.2 g/L), 0.186 NL/gVS, 0.191 NL/gVS, 0.203 NL/gVS, and 0.195 NL/gVS of CH4 were produced in reactors supplemented with GAC, GR, GO, and CNTs, respectively, compared to 0.177 NL/gVS produced in the control process. Likewise, at the end of the test (i.e., after 105 days at concentrations of C-based CMs half of the initial ones), CH4 yields were 0.193 NL/gVS, 0.201 NL/gVS, 0.211 NL/gVS, and 0.206 NL/gVS in reactors supplemented with GAC, GR, GO, and CNTs, respectively, compared to 0.186 NL/gVS of the control process. Especially with regard to GR, GO, and CNTs, results obtained in the present study represent a significant advance of the knowledge on the effects of such C-based CMs to realistic and scalable AD process conditions respect to previous literature.

Deep insights into the roles and microbial ecological mechanisms behind waste activated sludge digestion triggered by persulfate oxidation activated through multiple modes.

Persulfate oxidation (PS) is widely employed as a promising alternative for waste activated sludge pretreatment due to the capability of generating free radicals. The product differences and microbiological mechanisms by which PS activation triggers WAS digestion through multiple modes need to be further investigated. This study comprehensively investigated the effects of persulfate oxidation activated through multiple modes, i.e., ferrous, zero-valent iron (ZVI), ultraviolet (UV) and heat, on the performance of sludge digestion. Results showed that PS_ZVI significantly accelerated the methane production rate to 12.02 mL/g VSS. By contrast, PS_Heat promoted the sludge acidification and gained the maximum short-chain fatty acids (SCFAs) yield (277.11 ± 7.81 mg COD/g VSS), which was 3.41-fold compared to that in PS_ZVI. Moreover, ferrous and ZVI activated PS achieved the oriented conversion of acetate, the proportions of which took 73% and 78%, respectively. MiSeq sequencing results revealed that PS_Heat and PS_UV evidently enriched anaerobic fermentation bacteria (AFB) (i.e., Macellibacteroides and Clostridium XlVa). However, PS_Ferrous and PS_ZVI facilitated the enrichment of Woesearchaeota and methanogens. Furthermore, molecular ecological network and mantel test revealed the intrinsic interactions among the multiple functional microbes and environmental variables. The homo-acetogens and sulfate-reducing bacterial had potential cooperative and symbiotic relationships with AFB, while the nitrate-reducing bacteria displayed distinguishing ecological niches. Suitable activation modes for PS pretreatments resulted in an upregulation of genes expression responsible for digestion. This study established a scientific foundation for the application of sulfate radical-based oxidation on energy or high value-added chemicals recovery from waste residues.

Phages in sludge from the A/O wastewater treatment process play an important role in the transmission of ARGs.

Phages can influence the horizontal gene transfer (HGT) of antibiotic resistance genes (ARGs) through transduction, but their profiles and effects on the transmission of ARGs are unclear, especially in complex swine sludge. In this study, we investigated the characterization of phage and ARG profiles in sludge generated from anoxic/oxic (A/O) wastewater treatment processes on swine farms using metagenomes and viromes. The results demonstrated that 205-221 subtypes of ARGs could be identified in swine sludge, among which sul1, tet(M), and floR were the dominant ARGs, indicating that sludge is an important reservoir of ARGs, especially in sludge (S) tanks. The greater abundance of mobile genetic elements (MGEs) in the S tank could significantly contribute to the greater abundance of ARGs there compared to the anoxic (A) and oxic (O) tanks (P < 0.05). However, when we compared the abundances of ARGs and MGEs in the A and O tanks, we observed opposite significant differences (P < 0.05), suggesting that MGEs are not the only factor influencing the abundance of ARGs. The high proportion of lysogenic phages in sludge from the S tank can also have a major impact on the ARG profile. Siphoviridae, Myoviridae, and Podoviridae were the dominant phage families in sludge, and a network diagram of bacteria-ARG-phages revealed that dominant phages and bacteria acted simultaneously as potential hosts for ARGs, which may have led to phage-mediated HGT of ARGs. Therefore, the risk of phage-mediated HGT of ARGs cannot be overlooked.